Dulux Aquatech Waterblock 2K

Size
Paint Calculator
This product is currently out of stock, please visit a store or other online retailers.
Your Measurements:
Amount Needed:
For the best result we recommend to use {coatAmount} for {productTitle}
Key information
  • Finish Matt
  • Coverage 10-15 sqft/kg/2 coats
  • Drying Time 1-2 days after 1st coat; 4-6 days after 2nd coat
  • Coats 2
Product Features
  • 2K Cementitious Waterproofing coating
  • Excellent anti-alkali property
  • Suitable for waterproofing of sunken areas
  • Superior anti-carbonation property

Product Description

Aquatech Waterblock 2k is a specialist 2 component product that provides protection against water penetration for interior walls, bathrooms and kitchens. Its unique Hydro breathe technology prevents swelling, blistering and chalking of paint. The breathable coating prevents the top paint layer from peeling off. The coating is suitable to be applied on the interior surface of swimming pools before applying tiling or topcoat. The product can be applied in water tanks as well.

Application Description

Surface Preparation:
• For the Interior surfaces, existing POP or putty must be removed till the plaster surface is exposed.
• The surface must not be loose, it should be strong and free from dirt, dust, chalk, loose particles. This can be achieved by brushing with a wire/stiff coir brush, followed by water jetting if required or move the loose particles with air compressor.
• Oil or grease must be removed with degreasing solvents; otherwise it will hamper the performance of the product.
• Any cracks in the plastered surface should be filled with Aquatech crack fillers as per the requirement and other damaged surface should be repaired with cement and sand mixture or polymer modified repair mortar.
• Before application of the product, the surface must be pre wetted and saturated to a surface dry condition, which improves the bonding of water block 2K to the substrate.

Mixing Ratio: Waterblock 2K Solid Additive: Waterblock 2K Liquid Additive = 2:1 (By weight)

Mixing Procedure:
• After opening the mono carton, shake the liquid component properly for a homogeneous mixing. Transfer the entire liquid component to a clean mixing vessel and then slowly start adding the powder component under constant stirring with a stirrer using a pneumatic or electrical power tool (1KW) at slow speed of 200-300 rpm for 5-6 mins to get a homogeneous, free flowing and lump free mixture/slurry.

Application:
Interior Wall Application:
• Two coat of mixed slurry of Aquatech Waterblock 2K to be applied to the set concrete/Plaster @ 10 - 15 sqft/Kg by a masonry brush or appropriate powder spray equipment.
• The second coat should be applied when the first coat is completely dry. Drying time after the first coat should be 1-2 days.
• For Damp walls, ensure the full wall is applied with Aquatech Waterblock 2K.
• The treated area should be protected from direct sunlight and to be damp cured by covering with damp hessian or similar system.
• Allow the second coat to dry hard for 4-6 days. After proper drying the normal painting procedure for Primer, putty, Primer & top coat can be followed.

Concrete slabs or roof slabs:
• Two coat of mixed slurry of Aquatech Waterblock 2K to be applied to the set concrete/Plaster @ 5-6 sqft/Kg by a masonry brush or appropriate powder spray equipment.
• The second coat should be applied when the first coat is completely dry. Drying time after the first coat should be 1-2 days.
• Allow the second coat to dry hard for 4-6 days.

Water tanks and Swimming pools:
• Two coat of mixed slurry of Aquatech Waterblock 2K to be applied to the concrete/plastered surface @ 6- 7 sqft/Kg by a masonry brush or appropriate powder spray equipment.
• The second coat should be applied when the first coat is completely dry. Drying time after the first coat should be 1-2 days.
• Allow the second coat to dry hard for 4-6 days.
• For water tanks, both sides of the tanks should be covered for a better result.
• The treated area should be protected from direct sunlight and to be damp cured by covering with damp hessian or similar system.

Marbles/Stones:
• One coat of Aquatech Waterblock 2K slurry to be applied at the bottom side of the marble @ 2 mm + thick at coverage of approximately 5 sqft/Kg

Health & Safety

Treatments such as sanding, burning off etc. of paint films may generate hazardous dust and/or fumes. Wet sanding should be used whenever possible. Work in well ventilated areas. Keep out of reach of children. Refer Safety Data Sheet for more details.

Tips & Advice

  • 1. Preparing the Surfaces
    For the interior surfaces, existing POP or putty must be removed till the plastic surface is exposed, the surface must not be loose, it should be free from dirt, dust, chalk, loose particles.
  • 2. Cleaning
    Clean painting equipment immediately after use and dry
Fetching the data, please wait...